Avionics

Flap Motor connectors, Safety Wiring ( 2 hrs )

Crimped on connectors for Flap Motor.  Added spiral wrap protection and secured with cable ties.  Ready to enclose now with cover.  Started to safety wire bolts holding Wheel Fairing brackets on Main Gear.   First checked torque to confirm done, since hadn't marked with torque seal.

Flap motor connected.  Shown in end of travel

Decided to leave wheel fairing brackets on for first
 flight...so I went ahead and safety wired.

Avionics - Nav and Tail Lights

Tail Light installation ( 2 hrs )

Preparing to install Tail Light per OP56, I discovered this Suntail #LN-201-1 included Molex 5 pin connector.  But I only needed a 4 pin.   So I switched the unused Molex 4 pin connectors supplied with the Nav Light LN-201-1 to the Tail Light, and used the 5 pin connector for the RH Wingtip Nav Light (only 1, but better than none - see Jan 28 log).   Assembled  the 4 pin Molex for L1082 coming from aft fuselage (part of WH00057 harness).  [ note:  WH00057 harness already had female pins crimped - opposite of how Vans instructions showed.  Simply reversed connector and pins]   Crimped male pins/assembled 4 pin Molex to Tail Light.  Attached to Rudder Bottom Fairing w/  4-40 screws (strangely, Vans did not provide these screws in kit)

Switched 5 pin from Suntail so at least 1 Wing Tip -Nav Light
has a connector that matches the connector in Wing Harness

WH00057 harness from fuselage:  crimped on ring terminal for ground wire, and 4 pin connector with female pins

Tail Light with male  4 pin Molex

Suntail LN-201-1 Tail Light
installed.  Note drain hole
oriented toward bottom.

Avionics - Landing and Nav Lights

Landing and Nav Lights ( 2 hrs )

Primed and painted flat black both Landing Light brackets.  Crimped on ring terminals to wires per OP52A-02.   Follow up to Jan 26 entry: Vans product support (Gus) explained the 5 Pin Molex (Molex #03-06-2055) is no longer available (anywhere!...I checked), so in 2018 AeroLED changed to include Molex 4 Pin connectors in Nav Light kit LN-201-1.   Now, NOT compatible with WH00011 wiring harness installed 2 years ago that includes the female 5 Pin Molex.   Drat!  Gus recommended couple options, including simply plugging each male-female Pin together, covering with heat shrink tubing to retain and protect...when I install Wing Tip/Nav Light ass'ly.

painted flat black after priming

Per OP52A-02:  Ring terminals added. 
(One wire is terminated in butt splice)

Avionics - Nav Lights and Landing/Taxi Lights

Nav/Strobe Lights and Landing/Taxi Lights ( 4 hrs )

Completed mounting LH (green) and RH (red) Wing Tip Nav/Strobe Lights (Vans # LN-201-1)  per OP55-02 Steps 1-3.   Simple drilling and uni-bit to prep Wing Tip, then attached mounting plates.  Crimped Molex pins to 4 wires on each.  LN-201-1 comes with 4 Pin female Molex, but Wing kit wiring already has 5 Pin male Molex.  Aarrgghhh!  Vans OP55-03 shows 5 pin female Molex.  Since Wing has mounting slot set up for the 5 Pin, I'm contacting Vans to provide correct female 5 pin Molex connectors.   Meanwhile, completed Steps 1-4, Sect OP52A-01, "Aero LEDs Sunspot LX Landing and Taxi Lights":  Created (8) 10 mm long spacers.  Deburred all holes, edges and slots.   Added 8 nutplates.  Ready to prime and paint flat black.

RH ready to for mounting plate.  Slot allows Molex
connector to pass, if already done

Ready to mount light...but
added Molex pins first

RH side "done"...bottome LH light shown for reference

LH  done

time consuming to create 8 spacers each 10 mm long (w/o lathe)

deburring done...ready to add nutplates

Trial assembly.  Planning to prime and paint Mon
when weather is not so cold!

Firewall Forward Kit - Propeller

Spinner completed ( 3 hrs )

Loosened Spinner Plate from Prop Hub (actually removed nuts and washers so completely "off") so I could rivet Gap Fillers per Sect 44-07, Step 7.   Re-assembled & torqued Hub bolts/nuts to 21 ft-lbs per Hartzell Manual Table 3-1.  Trial fit Top Cowl to check gap to Spinner Plate.   Marked Spinner to trim to match edge of Spinner Plate.  Re-installed Spinner and sanded flush to edge of Plate completing Step 8, Sect 44-08.   Now done with Propeller and Spinner!

Spinner Plate loose from Hub to enable
riveting Gap Fillers

Re-installed Spinner Plate after riveting each Gap Filler.   Excess past edge of Spinner Plate yet to be removed

checking with Top Cowl to insure clearance, and
need to remove aft edge Gap Filler, as well as
similar overhang on Spinner.   ( after this pic, 
sanded Gap Filler and Spinner flush to aft edge
of Spinner Plate)

Firewall Forward Kit - Propeller

Spinner mounting ( 3 hrs )

Added remaining nutplates to Spinner Plate.  Checked fit of Gap Fillers and Spinner to Prop Blades as angled from min to max pitch per Step 6, Sect 44-07.  (per instructions, clamped 30" boards to blade about 10" from end for leverage).  Trimmed small amount fiberglass to meet 1/8" clearance.  Torqued and safety wired 4 bolts holding Front Bulkhead.  Started Step 7 to rivet Gap Fillers to Spinner Plate  - but determined I will need to loosen 4 bolts holding Plate to Hub to gain tool clearance.  At first it seemed I could rivet with Plate still in place, but 2 rivets are too close to blades for either "Main Squeeze", or rivet gun/bucking bar.  Drat...    Received shipment from Vans with my Landing Lights and Wing Tip Nav/Strobe Lights.   These are Aero LEDs recommended by Vans. 

Front Bulkhead for Spinner

All 22 nutplates and Screws installed.
Final clearance at Prop

Landing Light Kits...brackets, hardware

Nav /Strobe Lights for Wing Tips

Firewall Forward Kit - Propeller

Spinner nutplates ( 2 hrs )

Drilled #19 clearance holes for 6-32 attachment screws (AN526C632-R8).   Riveted on 6 nutplates to Front Bulkhead, then started on 14 nutplates on Spinner Plate.

nutplates on Front Bulkhead

Adding nutplates to Spinner Plate (bit more
challenging since remains bolted to Prop Hub