Dehydrator Plugs ( 1 hr )
Installed 4 Dehydrator Plugs (18mm). Needed trip to hardware store to get a long reach 7/8" socket for the aviation spark plugs. Terry Moushon (RV-10 builder and Tech Counselor) confirmed only four would be needed (one per cylinder). I'd need 14mm automotive size for the other 4 locations (due to E Mag installation).
I've started my adventure to build a Van's Aircraft RV14a. For several years, I've been planning to build an Experimental (homebuilt) airplane - once retired.
But first, I needed to get my Pilot's License. (Kinda key !) So... first things first: I retired March 2014 from Caterpillar - and started flying lessons in the Summer of 2014. Soloed a day after Christmas, and got my Private July 2015. Shop set up, tools acquisition, and practise kits during Fall launched me into my build starting Dec 31, 2015 !
I've chosen to build the RV14a since it's about 10% larger than Van's prior models - so it fits my 6'4" frame well. Van's is well known for great value & outstanding flying qualities. It's been a no brainer decision for me. A tour of their facilities and demo flight in Oct 2013 clinched the deal. My wife - also a pilot - exclaimed after her demo flight "retire NOW so you can build one of these". The RV14a fits my mission of a good compromise between cross country & aerobatics. Plus...I fit, too.
So far, one month into building, it's been rewarding. Very challenging, but certainly a learning experience. The builder community is terrific - as is Van's tech support. I'm finished with the Vert Stab and Rudder (Jan 2016). So... with a 5 month delivery lead time, I've ordered the Quick Build Wings and Fuselage.
I hope this blog assists other new builders, just like several others have been valuable to me. Plus it will serve to document my build step by step. Please drop me a line via the "contact me" form on lower RH margin.
Update: April 2020 relocated to Wickenburg, Az to escape Illinois winters.
Saturday, March 10, 2018
Friday, March 9, 2018
Firewall Forward
Fuel Flow Transducer ( 1 hr )
Installed IE Dynon FF Fuel Flow Transducer, including VA 102 Fuel Press Line and FF00019 Hose Ass'ly to Fuel Pump per Steps 1-3 at Sect 43-09, and Fig 1-4 at Sect 49-04. Installed EA LW-75444 Sniffle Valve to bottom of the oil sump per Step 4 at Sect 43-09.
Installed IE Dynon FF Fuel Flow Transducer, including VA 102 Fuel Press Line and FF00019 Hose Ass'ly to Fuel Pump per Steps 1-3 at Sect 43-09, and Fig 1-4 at Sect 49-04. Installed EA LW-75444 Sniffle Valve to bottom of the oil sump per Step 4 at Sect 43-09.
Thursday, March 8, 2018
Firewall Forward
Tuesday, February 13, 2018
Avionics and Firewall Forward Kit
Magnetometer connector and Engine fittings ( 1 hr )
Inserted 9 pins for wiring harness for CPC connector for GMU22 Magnetometer per Sect 62-02, Step 6 (rec'd connector from Stein Air...missed in earlier shipment of sensors, etc. ref Avionics Jan 25 entry). Added RC-1 CAP Tach Drive Cap per Sect 43-05, Step 7, and added plastic drain line FF00013 per Step 4 at back of engine driven fuel pump. [ Note from the future: will discover on April 23 that the Garmin Oil Temp Sensor is installed in wrong location as shown below in pic. Vans incorrectly shows this location in Sect 43-05, Fig 1. However, later Sect 51-06 correctly shows in place of red plastic cover closer to oil filter. Vans confirmed error on April 23. I exchanged locations and installed the original plug from Lycoming in place of where I originally installed sensor. See last pic showing RC-1 Cap below for incorrect location ]


![]() |
| RC-1 CAP in center of pic |
![]() |
| plastic drain line in center of pic |
Wednesday, January 31, 2018
Engine
Cotter Pins, etc ( 1 hr )
Added cotter pins to 4 castle nuts on engine mount bolts. The one at bottom mount under LH rear cylinder is tough to reach (see pics). Installed Oil Filler/Level Tube with safety wire.
Added cotter pins to 4 castle nuts on engine mount bolts. The one at bottom mount under LH rear cylinder is tough to reach (see pics). Installed Oil Filler/Level Tube with safety wire.
![]() |
| getting this cotter pin on was challenging...deep recess |
![]() |
| long needle nose, long screwdriver used to insert and bend ends |
![]() |
| safety wire on Oil Dipstick tube. close to engine mount, but clears 3/8" |
![]() |
| easy access to this cotter pin |
Tuesday, January 30, 2018
Engine
Engine Mounted ( 4 hrs )
Completed Sect 43-05 & -06 for fluid fittings, sensors on rear of engine. (did need to go to local store to purchase 13/16 deep socket, and 1" socket) Added the silicone hose to PMAG for the MAP connection. Mounted to firewall - carefully following instructions at 43-08 to insure "soft" vs "hard" durometer Dynafocal mounts were correctly positioned on top vs bottom (reversed). Contacted Vans tech support, and Eric Rushing confirmed the "EA Dyna VI - Std" are the correct rubber mounts, even though Vans instructions call out different part numbers. Using the Harbor Freight engine hoist worked out really well. Eric mentioned typically builders need a couple helpers to wrangle the engine into the mount locations. I started with top 2 mounts, aud used hoist to re-position engine until bottom mounts aligned. I don't need the sawhorse holding up aft fuselage -- plenty of noseweight ! I've been told engine needs to compress rubber mounts up to 2 months before aligning cowling,...so let the compression begin!

Completed Sect 43-05 & -06 for fluid fittings, sensors on rear of engine. (did need to go to local store to purchase 13/16 deep socket, and 1" socket) Added the silicone hose to PMAG for the MAP connection. Mounted to firewall - carefully following instructions at 43-08 to insure "soft" vs "hard" durometer Dynafocal mounts were correctly positioned on top vs bottom (reversed). Contacted Vans tech support, and Eric Rushing confirmed the "EA Dyna VI - Std" are the correct rubber mounts, even though Vans instructions call out different part numbers. Using the Harbor Freight engine hoist worked out really well. Eric mentioned typically builders need a couple helpers to wrangle the engine into the mount locations. I started with top 2 mounts, aud used hoist to re-position engine until bottom mounts aligned. I don't need the sawhorse holding up aft fuselage -- plenty of noseweight ! I've been told engine needs to compress rubber mounts up to 2 months before aligning cowling,...so let the compression begin!

![]() |
| glad able to add fluid fittings prior to mounting since some would be challenging to do after |
Monday, January 29, 2018
Engine
Big Day ! Engine delivered via UPS. Pleased "crate" was in great shape (clean, no marks or punctures). Tip N Tell indicated always upright too. Unpacking was easy, but took some maneuvering to enable lifting with my hoist. Started adding fluid fittings, ground strap, etc per Vans instructions in Sect 43-05 and -06. Especially on rear of engine, easier now than after mounted.
![]() |
| after unpacking, needed to switch ends of shop |
![]() |
| Tilt N Tell on right area...A OK. |
![]() |
| Engine number EL-691-80E |
![]() |
| standard Magneto.. |
![]() |
| and one EMAG's PMAG |
![]() |
| Engine Logbook, misc loose parts |


Subscribe to:
Posts (Atom)



























