I've started my adventure to build a Van's Aircraft RV14a. For several years, I've been planning to build an Experimental (homebuilt) airplane - once retired.
But first, I needed to get my Pilot's License. (Kinda key !) So... first things first: I retired March 2014 from Caterpillar - and started flying lessons in the Summer of 2014. Soloed a day after Christmas, and got my Private July 2015. Shop set up, tools acquisition, and practise kits during Fall launched me into my build starting Dec 31, 2015 !

I've chosen to build the RV14a since it's about 10% larger than Van's prior models - so it fits my 6'4" frame well. Van's is well known for great value & outstanding flying qualities. It's been a no brainer decision for me. A tour of their facilities and demo flight in Oct 2013 clinched the deal. My wife - also a pilot - exclaimed after her demo flight "retire NOW so you can build one of these". The RV14a fits my mission of a good compromise between cross country & aerobatics. Plus...I fit, too.

So far, one month into building, it's been rewarding. Very challenging, but certainly a learning experience. The builder community is terrific - as is Van's tech support. I'm finished with the Vert Stab and Rudder (Jan 2016). So... with a 5 month delivery lead time, I've ordered the Quick Build Wings and Fuselage.

I hope this blog assists other new builders, just like several others have been valuable to me. Plus it will serve to document my build step by step. Please drop me a line via the "contact me" form on lower RH margin.
Update: April 2020 relocated to Wickenburg, Az to escape Illinois winters.

Friday, July 5, 2019

Finish Kit (and others for Final Assembly)

ELT tested, G3x data logger, etc ( 5 hrs )

During past couple days, working to prepare for Airworthiness Inspection, and First Flight.  Cleaned Canopy of some residue left from sticky plastic layer (Plexus spray, and some isopropyl alcohol).  Removed Spinner so I could removed protection tape off blade roots.  Tested ELT Model E-04 (emergency locator transmitter) per Sect 9 in ACK Tech, Inc manual.  I heard a tone from my hand-held radio tuned to 121.5, and beep from system in plane.  (note: I called AFRCC #800-851-3051 first, but contrary to other info, they don't need coordination of self-test for 406 MHz systems)  Also verified receiving GPS data per Fig 134, page 9 re: test tool set-up.  ACK Tech confirmed using voltmeter on test lead was acceptable alternative to using an LED & 300 Ohm resitor.  Saw "pulse" every second as expected.   With Nancy's help, did another engine run for few minutes - this time insured I turned on Alternator power ! - immediately confirmed charging battery as volts increased, and Amps display registered high current tapering off quickly as battery recovered from start.  Removed SD card, and charted data on home PC.  (prior run July 2 was first time used SD card in G3X to record.  I'd forgot to turn on Alt Pwr, so I was concerned when data showed NO charging of battery, and 0 Amps.  Now using checklist w/ engine runs to insure I turn on Alt)  Rick Olson, friend in area who recently built a RV-4 stopped by to see my status.  He spent about an hour "inspecting" and found a couple minor things, which I quickly "fixed"...see pics below.  Thanks Rick !
Modified plug rack to fit the 4 "Automotive"  14mm plugs
for the PMAG.  Epoxied on 1/2" ID aluminum washers,
replacing the cardboard "fix" Terry created on day of 1st run.

Per Rick's recommendation (Terry had suggested earlier too),
I  constrained the PMAG leads on top cylinders to adel style
clamp on injection fuel line

Rick found the blue T fitting on MAP line had slipped out of
adel clamp - so I re-positioned clamp, and shoved  "T" much
farther in.  Seems secure now, but I'll continue to examine

example screenshot.  Terry reminded me easy to do on G3X...
simply hold "menu" key down for few seconds.  This was
several minutes after today's engine run...CHTs (stopped
run once reached 250F) and EGTs were lower

No comments:

Post a Comment